Kitchen Tap Replacement Croydon
Kitchen tap leaking, loose at the base, hard to turn, or ready to swap for a new kitchen mixer tap? MPS Heating & Plumbing LTD replaces kitchen taps, sink taps and kitchen tapware across Croydon.
We remove the old tap, fit the new kitchen tap properly, check the flexible hoses, isolation valves and pipework underneath, then test for leaks before leaving. It sounds like a small job. It is. But when it is rushed, the leak usually shows up inside the cupboard later.
This page sits inside our Plumbers Croydon cluster, which keeps tap work connected to the rest of the local plumbing pages without mixing it up with boiler repairs or servicing.
62 Reviews
8am–2am
South London
Book a plumber to change your kitchen tap
Kitchen tap replacement is usually straightforward, but the awkward bit is rarely the tap you can see. It is the back nut behind the sink, the old copper pipe, the isolation valve that has not moved for years, or the waste trap sitting exactly where your hand needs to go.
We fit kitchen taps, kitchen sink taps, sink taps, kitchen mixer taps, kitchen tap mixer setups and modern tapware. If you have already bought a tap from Screwfix, B&Q, a kitchen supplier or online, we can usually fit it as long as it suits the sink and the water pressure.
Chrome, black, brushed steel, pull-out spray tap, monobloc mixer tap, even a gold kitchen tap. The finish does not matter as much as the fittings underneath.
Common jobs
- Replacing a dripping kitchen tap.
- Changing an old kitchen mixer tap.
- Fitting Screwfix kitchen taps or B&Q kitchen taps.
- Sorting a loose tap at the kitchen sink.
- Checking weak hot or cold flow from a mixer tap kitchen setup.
- Replacing kitchen sinks and taps during a small kitchen refresh.
- Checking under-sink pipework for slow leaks.
How long does changing a kitchen tap take?
Most kitchen tap replacements take around 45 to 90 minutes. Not every job, but that is a realistic guide for a normal tap swap.
| Kitchen tap situation | What usually needs doing | What can slow it down |
|---|---|---|
| Modern kitchen mixer tap | Remove old mixer tap, seat the new tap, connect hot and cold tails, then leak test underneath. | Tight cupboards, awkward back nuts, sink waste pipe in the way or old fixings seized solid. |
| Older kitchen sink tap | Isolate water, remove old fittings carefully, fit the new kitchen sink tap and check the pipework. | Brittle copper, poor isolation valves, old washers, damaged flexi hoses or stiff stopcock. |
| Screwfix taps or B&Q taps | Check the tap, fittings, washers and flexible hoses before fitting. | Wrong tap type, missing parts, tap not suitable for the property pressure or mismatched connections. |
| Weak flow from the new tap | Check valves, hose kinks, filters, debris and whether the tap suits your hot water setup. | Existing pressure issue, partly closed valve, old pipework or a separate hot water problem. |
What we check under the sink
- Hot and cold feed connections.
- Flexible tap hoses.
- Isolation valves.
- Tap fixing and stability.
- Washers, seals and compression fittings.
- Water flow from the kitchen mixer tap.
- Slow leaks below the sink after testing.
The leak is often underneath
The tap can look perfect from above and still be wrong below. A slightly twisted flexi hose, a missing washer or a compression fitting that is just not sitting right can cause a slow drip. Not always straight away either.
That is why we do not just fit the tap and walk off. We run hot and cold water, dry the fittings, check again, and look around the cupboard base. A few extra minutes here can save a swollen kitchen unit later.
If the problem is actually a pipe joint or hose leak, our leaking pipe repairs Croydon page is the better match.
Have the new tap ready?
Call us and talk through the tap type, access under the sink and whether there are any other small plumbing problems worth checking while we are there.
Kitchen tap installation in Croydon homes
Croydon homes are mixed. Some kitchens have neat modern pipework with local isolation valves. Others have years of small changes under the sink. Washing machine feed added later. Dishwasher valve squeezed in. Waste trap too close to the tap tails. You see it a lot in older terraces and conversions.
Flats near East Croydon and West Croydon can be tighter again. Less room in the cupboard, shorter pipe runs, and sometimes poor valves that make isolating the water awkward. We check before forcing anything, because that is how a small tap job becomes an emergency plumbing job.
Quick real-world example
One of the common ones is a customer thinking the new tap is faulty because the hot side is weak. Under the sink, the isolation valve is only half open, or the flexi hose is kinked. Another one is a tap that works fine from above, but there is a tiny weep underneath.
Not dramatic on day one. A month later, the cupboard base is soft. That is why the checking matters.
Related plumbing help in Croydon
Main hub for local plumbing work, including taps, leaks, toilets, sinks and general plumbing issues.
Use this if water will not isolate, the leak is active, or the job cannot wait.
Wider plumbing service page for mixed jobs that do not fit one single problem page.
For slow kitchen sinks, smells, gurgling or water backing up in the bowl.
For water below the sink, leaking flexi hoses, damp cupboards or pipe joints dripping.
For weak flow from taps, showers or several outlets across the property.
For toilets that keep running, cisterns overflowing or overflow pipes dripping.
For water around radiator valves, pipe joints or the radiator body.
For old, leaking or poor-performing radiators that are better replaced than patched.
Kitchen taps, hot water and boiler checks
Replacing a kitchen tap is plumbing work, not gas work. But sometimes people mention hot water while we are already at the sink. If the hot water is weak only at the kitchen tap, it may be the tap, valve, hose or filter. If your radiators are heating normally but every hot tap in the house runs cold, read our No Hot Water But Heating guide. If the boiler is showing a fault or needs diagnosing, our Boiler Repairs page is the best place to start.
- Boiler installation Croydon for old or unreliable heating systems that need replacing.
- Boiler replacement Croydon if you are comparing replacement options for an older boiler.
- Boiler repairs Croydon if the hot water problem is boiler-related and needs diagnosis.
- Boiler Repairs Croydon if the boiler has stopped working or keeps failing.
- Annual boiler service if the boiler is working but due a proper yearly service.
- New boiler or service? if you are unsure whether the heating system needs repair, service or replacement.
Gas Safe note
Kitchen tap fitting is normal plumbing work. Boiler repairs, gas boiler servicing and boiler installation are different. For gas and boiler work, MPS Heating & Plumbing LTD is Gas Safe Registered — ID 662170.
MPS Heating & Plumbing LTD
46 Broughton Road, London, CR7 6AL
Phone: 0203 576 6769
Email: info@mpsheatplumb.com
Hours: Monday–Sunday, 08:00–02:00
Kitchen Tap Replacement FAQs
Do you supply the new kitchen tap or fit one I have bought?
We can fit a kitchen tap you have already bought. Many customers buy kitchen taps from Screwfix, B&Q, online suppliers or kitchen showrooms. Send a photo if you want us to check whether it looks suitable before booking.
What types of kitchen taps can you fit?
We fit standard kitchen taps, kitchen mixer taps, monobloc mixer taps, pull-out spray taps, kitchen sink taps, sink taps and modern kitchen tapware including chrome, black, brushed steel and gold kitchen tap designs.
How long does changing a kitchen tap take?
Most kitchen tap replacements take around 45 to 90 minutes. It can take longer if the old tap is seized, the isolation valves do not work, access is tight or the pipework needs adjusting.
How do you replace a kitchen tap?
The water is isolated first. The old hot and cold connections are disconnected, the fixing nut is removed, and the old kitchen tap is lifted out. The new tap is then seated, secured, connected and tested for leaks.
How do you replace a kitchen mixer tap?
To replace a kitchen mixer tap, both hot and cold feeds are isolated and disconnected. The old mixer tap is removed, the new kitchen mixer tap is fitted through the sink or worktop, then the flexible tails are connected and tested.
How do you replace a washer on a kitchen tap?
Older kitchen taps may use washers, while many modern mixer taps use cartridges. If the tap is old, stiff or badly worn, replacing the whole kitchen tap may make more sense than trying to change a washer.
Can I change a kitchen tap myself?
You can change a kitchen tap yourself if you can safely isolate the water, remove the old fittings and connect the new tap correctly. The tricky parts are usually seized fixings, old valves, tight access and checking for leaks afterwards.
Do you need a plumber to change a kitchen tap?
A confident DIYer may manage a simple kitchen tap swap. A plumber is sensible if the fittings are old, the stop valve is stiff, the pipework is awkward, or you want the job checked properly before the cupboard goes back to normal.
Why is my new kitchen tap water flow weak?
Weak flow can come from a partly closed isolation valve, kinked flexible hose, debris in the tap filter, low water pressure or a tap that does not suit the system. If several taps are weak, see our low water pressure page.
Can you look at other small plumbing jobs during the same visit?
Usually, yes. Let us know if you also have a blocked sink, leaking pipe, poor water pressure, dripping valve or another small plumbing issue. We can allow time where possible.
How much does it cost to change a kitchen tap?
The cost depends on access, the old tap, the new tap, and whether any valves or pipework need attention. For general guidance, you can check our pricing page.
What if my tap is described as faucet faucet or mixer faucet?
Some product listings use American wording like faucet, mixer faucet or kitchen faucet. In the UK, we normally call it a kitchen tap or kitchen mixer tap. If the fittings are compatible, we can usually fit it.